loading curve造句
例句与造句
- The unloading curve normally falls below the loading curve to form a hysteresis loop .
卸载曲线通常都落在加载曲线之下，形成一个滞后回线。 - Upon unloading at any state in the deformation, the strain does not retrace the loading curve but is reduced along an elastic unloading line .
在变形的任一阶段卸载时，应变都不按加载曲线返回，而是沿着弹性卸载曲线下降。 - Monthly load curve
月负载曲线 - Annual load curve
年负荷曲线 - It is shown that permitted load curve must be implemented in choosing crank press
在选用压力机时，必须严格按照许用负荷曲线图来选择。 - It's difficult to find loading curve in a sentence. 用loading curve造句挺难的
- Combining it with the standard daily load curve can make the mean daily forecasting error with in 2 %
将其与标准日负荷曲线取平均作为预测结果，示例表明日平均误差小于2 % 。 - With the proposed method , the internal operation of lijiaxia hydropower station is optimized and the optimized load distribution is derived based on three characteristic daily load curves
运用上述方法，分别以3条特征日负荷曲线为依据对李家峡水电站的厂内运行进行了优化，并得到其负荷分配方案。 - By effectively managing and controlling of electric load , we can improve load curve and advance using rate of power supply equipment , which can prevent from drawing strobe and limiting electricity and avoid affecting social produce and life
对用电负荷进行有效的管理和控制可改善负荷曲线，提高发供电设备的利用率，可防止拉闸限电，避免影响社会生产和生活。 - This software can not only measure the real time data of hydroelectric plant , but also carry out the auto generate electricity on the hydroelectric plan t and ordinal startup - stop of the dynamotor . the software also carrys out the functions of alarm disposal , report forms , print and load curve
该软件不仅实现了对水电站内各种模拟参数和数字信号的实时监测功能，还实现了对水电站的自动发电、机组顺序启停的控制，以及报警处理、报表打印、负荷曲线等功能。 - In different in terne die travel , the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve . . at the same time , we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally , the optimized technics parameters were used into pilot production , then the qualified oil pump stator forging were produced , the analog results were compared with those of pilot production
论文具体分析研究了不同成形工艺过程中金属流动的特点，并对不同凸模行程下温挤成形过程中的金属流动特点、坯料连皮厚度(底部高度)与温挤压成形工艺中的轴向界限尺寸的差值对金属变形阶段的影响进行了分析，获得了坯料在不同凸模行程下的等效应变场、速度场等场变量及凸模行程-载荷曲线，同时对油泵定子成形过程的影响因素等进行了分析，优化并获得了合理的温挤成形工艺及模具参数。最后，利用模拟优化获得的各项工艺参数进行生产实验，得到实际生产出的合格油泵定子件，并将模拟结果与生产实验结果进行比较。 - 4 . 1n power market , the load changes randomly and quickly and sometimes the load curve takes on the " pinpoint - peak " , so the reserve capacity is difficult to be ascertained , in the meantime , the customers require some options . the above - mentioned reasons are particularized in this paper . a method that the large customers and generator units are permitted to bid and be queued , then be dispatched in real time in ancillary services market is put forward
根据负荷变化的随机性和快速性，负荷的“针尖峰”存在，备用容量难以确定，以及用户需要更多的选择权利等因素，提出了可以允许具备条件的大用户和发电机组同时参加备用市场的竞标排序，并按排序结果进行实时调度。 - First , build the building model and air conditioning dynamic cooling load analysis model of the stock exchange in the basis of the experiment . second , calculate the air conditioning dynamic cooling load in summer ( april to october ) hourly by software simulation , obtain the maximum cooling load daily , the minimum cooling load daily , the proportion of each cooling load occupying the total cooling load and cooling load time frequence , analyse them by using twin load curves . last , contrast theoretical calculations with test results , analyse them and prove the model proper
首先，以实验为基础建立了证券营业部的建筑模型及空调动态冷负荷分析模型；其次，通过逐时逐日计算出了其夏季( 4月? 10月)空调动态冷负荷、各分项冷负荷在空调总冷负荷中所占的比例及空调冷负荷时间频数，并运用双负荷曲线法对每日最大冷负荷与每日最小冷负荷进行分析；最后，与实测数据进行对比，二者曲线基本符合，效果良好，证明所建模型适当。 - The contrast test between self - balance test and top load test has been done applying the research of the article , it shows that the transferred curves are well consistent with top load curves , so it can satisfy the engineering requirement and its accuracy can amount to about ninety percent
结果表明：自平武汉理工大学硕士学位论文衡试桩法与传统静载试验具有较好的一致性;采用本文的提出的数据转换分析方法，转换曲线与传统静载曲线吻合性较好，极限承载力的判定误差在10 %左右，能够满足工程精度的要求。 - The adopted alternative coefficient for capacity is from 1 . 05 to 1 . 10 and for electric generation 1 . 05 . in fact , the capacity benefits are related to maximum load , load curve and the weight of hydropower power capacity . while the benefits of coal consumption saving are related to load consumption characteristic and power structure in addition to maximum load and load curve of the power system
当系统的水电(含抽水蓄能)比重较小时， 1 . 05 1 . 1容量替代系数可能偏小；而当抽水蓄能电站占有一定比重时，这种方法又可能过高地估计了抽水蓄能电站的容量效益，因为它未能考虑某些月份抽水蓄能电站可能出现的空闲容量。 - So how to transfer scientifically self - balanced test data into top load curve according to its actual working behavior , become the obstacle of its practical application . in accordance with actual forcing behavior and reaction mechanism between pile and soil , the article analyzes the relation between top part and bottom part , load transferring mechanism and difference with other loading way by ansys program . so the reliability of determine bearing capacity by self - balance method has been proved
本文根据自平衡加载方式下桩身的实际受力状况、桩土间的相互作用机理以及单桩破坏机理，建立了单桩的离散元模型，采用ansys通用分析软件，选取合理的单元类型、材料特性等，数值分析了基桩在自平衡加载方式下上下桩段的相互关联、荷载传递机理以及与其它加载方式的区别，论证了采用自平衡试桩法测定单桩极限承载力的可行性。